The 3508 large 5-digit display provides a clear and unambiguous indication of the process value. A four-line message centre provides custom or standard views of important information to the user while vertical and horizontal bargraphs provide at a glance visual indication of the process.

The Eurotherm 3508 is a 1/8 DIN process controller belonging to the most advanced range of products in this category. It offers precision control of a range of process variables, such as temperature. It has advanced features that offer great flexibility.

For configuring basic functions, including control options, alarms, sensor type, and measurement range a 'Quick Start' process can be used. The unit combines flexibility with ease of use. For configuring advanced features, users can use a PC based tool that allows them to select functions from a library.  

Ideal for:
Semi-conductors
Process applications
Reactors and Fermenters
Autoclaves
Environmental chambers
Melt pressure
Heat Treatment

Features:
Precision PV input
Math/logic/timers
Modbus RTU
Recipes
50 Programs
Carbon potential
Ethernet Modbus TCP
2 PID loops
Custom user interface
Profibus DPDeviceNet network

The “EPACK-2PH” and “EPACK-3PH” has been added to the Power Control section of our Eurothermonline store. For those who wish to upgrade their furnaces or heating equipment from analog to digital SCRs, the EPack is the perfect solution for OEMs and End Users.

A current transformer input provides display of the heater current and a health check on the load. Partial load failure, heater open circuit and SSR faults are detected and displayed as scrolling alarm messages as well as providing an alarm output. A front panel ammeter displays the heater current on the 3204.

The Eurotherm 3216 is Quick and easy commissioning - no need for expert knowledge. Clear information of process with scrolling, custom messages. Custom alarm messages for easy understanding. Recipe selection from operator interface. Internal timer and set point programming. Instant indication of heater faults with integral ammeter. Remote set point - solution for multi-zone applications.

The Eurotherm 3216 controller comes with many advanced features that are not available that are commonly available in similar controllers. It provides precision control of process variables like temperature.

Here’s an outline that describes the status messages for the Eurotherm 2704 Multi Loop Controller. These messages appear on the display to show the status of the controller.

The 3508 large 5-digit display provides a clear and unambiguous indication of the process value. A four-line message centre provides custom or standard views of important information to the user while vertical and horizontal bargraphs provide at a glance visual indication of the process.

The Eurotherm 3508 is a 1/8 DIN process controller belonging to the most advanced range of products in this category. It offers precision control of a range of process variables, such as temperature. It has advanced features that offer great flexibility.

For configuring basic functions, including control options, alarms, sensor type, and measurement range a 'Quick Start' process can be used. The unit combines flexibility with ease of use. For configuring advanced features, users can use a PC based tool that allows them to select functions from a library.

Ideal for:
Semi-conductors
Process applications
Reactors and Fermenters
Autoclaves
Environmental chambers
Melt pressure
Heat Treatment

Features:
Precision PV input
Math/logic/timers
Modbus RTU
Recipes
50 Programs
Carbon potential
Ethernet Modbus TCP
2 PID loops
Custom user interface
Profibus DPDeviceNet network

A universal input enables selection of nine internally stored thermocouple types and the PT100 resistance thermometer. Linear inputs can be scaled to the desired display range. Two relay outputs are configurable for alarms. Three internal alarm setpoints are provided- configurable as high, low or deviation. Alarms can be 'blocked' on start-up to prevent unnecessary operator alerts.

2100 Series Controller
The compact Eurotherm, 1/32 DIN panel size, 2132 temperature controller uses advanced PID algorithms to give stable temperature control. Specialist knowledge or training is not needed to optimize the control performance, because Self-tuning is included.

• Simple operation
• Three internal alarms
• Up to two relay outputs
• One logic input or output
• Reliable performance and accuracy
• Internal timer - a 5 mode timer suitable for simple time based profiling applications
• Universal input - 9 thermocouple types, PT100, DC linear and a downloadable custom curve

Universal input/two outputs
Linear inputs can be scaled to the desired display range. A universal input enables selection of nine internally stored thermocouple types and the PT100 resistance thermometer. Other input linearizations may be factory downloaded. Two outputs are configurable for heating, cooling or alarms.

Operator interface
The operator interface can be customized to present only those parameters that an operator needs to see and adjust, while other parameters are locked away under password protection.

Internal alarm set points
Alarms can be 'blocked' on start-up to prevent unnecessary operator alerts. Three internal alarm set points are provided - configurable as high, low or deviation alarms.

Heater failure can be detected using PDSIO when the controller is used with a TE10S Solid State Relay - this negates the need to use extra components such as current transformers.

Internal timer
A five-mode timer is provided for simple, time-based profiling applications. Ideal for:

• Trace heating
• Sterilizers
• Chillers
• Plastics - extrusion
• Heat treatment -small ovens
• Heat sealing

Features:

• Customized operator interface
• Three internal alarm set points
• Universal input selection
• Two configurable outputs
• Heater failure detection
• Tactile buttons

The 2408i provides accurate measurement with flexible functions. Accurate, stable measurement of temperature, pressure, level, flow and other process variables are provided by the 2408i. An optional second process value input allows the average, difference, minimum or maximum of two values to be displayed. Large, bright, red or green displays ensure good visibility in high and low ambient lighting.

The 1/8 DIN Eurotherm 2408i makes process and temperature measurements easy by providing alarming and indication functions. Relay outputs are used to implement process interlocks, such as over temperature furnace limits.

• Extrusion melt pressure indication and alarming
• Modular construction offering increased I/O flexibility
• Second process input provide additional alarming strategies
• Furnace over temperature limits
• Large 5 digit display providing excellent visibility
• Fieldbus communications providing system integration

The unit helps users select from the 9 available sensor types that are store internally, with its universal input capability. Users can scale linear input as desired. For more input linearizations, users can use iTools for download. Indication of non-linear signals is achieved using the 15 point linearization.

The process value is clearly displayed on the green or red 5 inch display. For displaying and alarming on the maximum, minimum, average, and difference of two values, the second process input can be used.

The unit provides great flexibility by allowing the attachment of up to 3 I/O modules from the available 9. Conventional analog retransmission or digital communications can be used to achieve system integration.

Applications include:

• Plastics processing - Extrusion melt pressure
• Heat treatment - Furnace over temperature
• Temperature & process indication
• Process protection
• Weighing platforms

Features:

• Universal input
• Profibus DP
• Strain gauge input
• Serial Modbus™ comms
• Red or green display
• Process variable retransmission
• Devicenet

The Mini8 controller is an ideal partner to a programmable logic controller. Able to multi-drop on either Serial, Fieldbus or Ethernet communications. It offers a cost-effective alternative to performing analogue measurement or loop control in a PLC. The Mini8 Controller, a very competitive and compact data acquisition device, offers high performance control usually only found in Eurotherm panel mount PID controllers.

Its modular design enables its I/O and feature set to be selected to meet a wide range of applications from simple to complex.

The ideal partner to a programmable logic controller (PLC) is the Mini8 controller. It is able to multi-drop on either serial, Ethernet or Fieldbus communications and it offers a real, cost-effective alternative to performing loop control or analog measurement in a PLC.

By implementing these functions in the Mini8 controller hardware cost is reduced, relieving the PLC of the burden of performing analog functions - often allowing a lower specification processor to be used.

The feature set of the Mini8 controller includes graphical wiring, high performance PID control, and set-point programming functions together with logic, math and timing function blocks.

When used in a data acquisition installation the high density analog I/O can be combined with paperless graphic recorder products, like the Nanodac to provide unsurpassed local and network access to your process.

Eurotherm 1/4DIN panel mount Nanodac™

Recorder/Controller offers graphical recording combined with PID control. Features & Options: 4 universal inputs, up to 2 PID loops, outputs and digital communications. Options must be specified when ordered.

Ordering options are

In it’s a box size the nanodac™ recorder/controller offers the ultimate in graphical recording combined with PID control. The compact ¼ DIN panel mount unit offers 4 high accuracy universal inputs for data recording and PID control. This secure data recording device with accurate control is enhanced by a full color, ¼ VGA display to bring a crystal clear operator interface to even the smallest of machines.